STAYING SAFE ON THE ROAD

Understanding CE Ratings for Motorcycle Gear

You'll see us mention CE ratings all over our website, and for good reason. It's the easiest way to tell whether a jacket, pair of pants or set of armour has actually been tested to protect you in a crash, or just looks the part.

Here's what the ratings mean, what the gear goes through to earn one, and what to look for when you're shopping.

CE stands for Conformité Européenne (European Conformity). In Europe, motorcycle clothing counts as personal protective equipment, so it can't be sold there unless it's been tested by an independent lab and passed.

For riding gear, that means the lab has checked how it holds up in a slide, how well the armour softens an impact, and whether the garment stays together and stays in place while it's doing its job.

Each type of gear has its own standard, so the number on the label tells you what was tested:

  • Jackets, pants and suits: EN 17092, rated AAA, AA, A, B or C.
  • Armour: EN 1621-1 for shoulders, elbows, hips and knees, EN 1621-2 for back protectors, EN 1621-3 for chest protectors. Rated Level 1 or Level 2.
  • Gloves: EN 13594, rated Level 1 or Level 2.
  • Boots: EN 13634, shown as four numbers covering height, abrasion, cut resistance and crush resistance. Our boot ratings guide goes through these.
  • Helmets: a separate system again, ECE 22.06 (or the older 22.05).

Anyone can sew a few pads into a jacket and call it protective. A CE rating means someone independent has checked that claim.

  • The whole garment has been tested by an outside lab, not just the brand.
  • The rating gives you a real way to compare one jacket with another.
  • You can match the level of protection to the riding you actually do.

CE Ratings for Clothing

Jackets, pants and suits are rated under EN 17092. The class is for the whole garment, not just the fabric:

  • AAA: The highest level. Think leathers and serious touring or adventure gear for fast road riding and track days.
  • AA: Strong protection for touring and everyday road riding. Often a good balance of protection, comfort and airflow.
  • A: Lighter protection made with commuting and city riding in mind.
  • B: The same abrasion level as A, but sold without impact armour.
  • C: Armour carriers that hold protectors in place but aren't made to be worn on their own. Some armoured base layers are Class C, but plenty, like Pando Moto and Knox, are tested as full garments and rated A, AA or AAA.

CE Ratings for Armour

Armour is tested by dropping a weight onto it and measuring how much force gets through to the other side. Less force through means better protection.

CE Level 1

  • Softer and more flexible, so it's comfortable and easy to move in.
  • Good for commuting and everyday riding.
  • Limb armour: no more than 35 kN on average. Back protectors: no more than 18 kN.

CE Level 2

  • Lets through a lot less force than Level 1.
  • Common in touring, adventure and sports gear.
  • Can be a little thicker, though modern Level 2 armour is often barely bulkier than Level 1.
  • Limb armour: no more than 20 kN on average. Back protectors: no more than 9 kN.

WHAT GETS TESTED

What a garment goes through to earn its rating

An EN 17092 rating isn't just a sliding test. The garment is split into zones based on where riders tend to hit the ground, like shoulders, elbows, hips, knees and the seat, and the higher-risk zones have to hold up for longer. Here's what's checked:

  • Abrasion resistance. Every layer of the garment is tested together: outer shell, membrane, lining and any padding. The only thing left out is the armour, which is tested on its own. This is how the lab works out how long the garment lasts sliding along the road before it wears through.
  • Impact energy absorption. The armour has to be certified to EN 1621, and it has to sit in the right spots on the garment. AAA, AA and A gear must come with it.
  • Seam strength and structural closures. A jacket is only as strong as its stitching. Seams are pulled to see how much force they take before they split, and zips, press studs and other closures are checked so the garment doesn't burst open in a fall.
  • Tear strength. Once a material is nicked or snagged, how easily does it rip? This test makes sure a small cut doesn't turn into a big hole.
  • Sleeve restraint. For jackets and one or two-piece suits. Sleeves are tested to make sure they won't ride up your arm in a slide and leave your skin and elbow armour exposed.
  • Fit and ergonomics. The garment is checked in the riding position to make sure the armour stays where it should and you can still move and control the bike properly.
  • Dimensional stability after washing. The garment is washed following its care label, then measured. If it shrinks or warps, the armour might not line up anymore, so it has to come out the same size it went in.
  • Innocuousness. The materials are checked for harmful chemicals, since this is gear you'll wear against your skin for hours.

A garment only gets its class if it passes all of these. That's why you can find a jacket made from AAA-level fabric that's rated lower overall. Weak seams, sleeves that ride up or thin material in one zone will pull the whole rating down.

CE Ratings and Australian Brands

We stock a big range of CE-rated gear. We also love supporting small Australian brands and giving them a place to grow.

It's worth knowing that Australian brands don't have to get CE certified unless they sell into Europe. Some do their own in-house testing, which can be very thorough, but the product won't carry a CE mark unless it says so on the label.

If you're planning on fast or long-distance riding, it's something to keep in mind when you're choosing gear. If you're not sure, just ask us.

Check the label sewn inside the garment. A rated jacket or pair of pants will show the CE mark, a motorcyclist pictogram, the standard (EN 17092) and its class, for example AA.

Armour has its own stamp or label showing the standard and the level, and usually the body part it's made for.

Sometimes only the armour is rated, not the jacket. Some brands, especially at the budget end, will say their gear is "CE approved" when all that's been tested are the pads inside.

CE armour in an untested jacket doesn't make it a rated jacket. The fabric could wear through quickly, the seams could split, or the sleeves could ride up and take the armour with them.

Look for EN 17092 and a class on the garment label itself. If you're still unsure, ask the brand for its CE certificate. Brands that have passed are usually happy to share it.

MotoCAP (Motorcycle Clothing Assessment Program) is an independent Australian and New Zealand program that buys gear off the shelf and tests it. It's backed by government road safety agencies, insurers and transport organisations.

Each item gets two scores:

  1. Protection: how well it holds up against abrasion, impact and seams bursting in a crash.
  2. Breathability: how well it handles heat and sweat, which matters a lot in an Australian summer.

MotoCAP is useful, but it's optional and only covers a small slice of what's on the market. CE certification is required for anything sold in Europe, so it covers far more gear. That's why we lead with CE ratings. You can read more on our CE ratings and MotoCAP page.